By Steve Kuhn | Last updated: October 21, 2026
A water filter for well water only fixes what it was built to fix. A carbon filter can clear up a sulfur smell and still won’t effectively remove nitrate. A softener handles hardness but may remove only a limited amount of dissolved iron. So start with what’s in your water.
That matters in western Dane County. When the county tested 183 private wells in the Town of Cross Plains in 2025, about 1 in 10 came back over the federal nitrate limit. You won’t see or smell nitrate in a glass of water.
Short answer: test first, then filter. Sediment filters catch grit. Iron filters handle iron, softeners handle hardness, RO cuts nitrate at one tap and UV kills bacteria. Wisconsin requires an approved device and a licensed installer, unless you fit it in the one-family home you own and live in.
What a well water filtration system is
A well water filtration system is equipment on your water line that removes specific problems, such as sediment, iron, hardness or bacteria, from well water.
Some systems treat every drop that comes into the house, while others sit under one sink and treat only the tap water you drink and cook with. Reverse osmosis units, for example, often come with a sediment filter and a carbon filter built in.
City water must be tested regularly and meet state and federal standards. A private well doesn’t. UW Extension notes that well owners are under no obligation to correct water quality problems, so checking and treating well water falls to homeowners.
Which filter removes what from well water?
Each filter type handles a short list of problems. Match it to your lab results: sediment goes to a particle filter, iron to an iron filter, nitrate to RO.
Here’s how the common options line up, based on the University of Wisconsin Extension guide for private well owners.
| Problem | Usual fix | Limit worth knowing |
|---|---|---|
| Sand and silt | Sediment (particle) filter | a sediment (particle) filter. Expect frequent cartridge changes if your well carries heavy sediment. |
| Iron and manganese | Iron filter using greensand or manganese dioxide resin | an iron filter, which uses filter media such as greensand or a manganese dioxide resin. The guide calls these especially useful between about 3 and 10 mg/L of iron. |
| Heavy iron, above 10 mg/L | Chemical oxidation or aeration, followed by filtration | chemical oxidation or aeration, followed by a filter that catches the particles. |
| Hardness from calcium and magnesium minerals | Water softener | a water softener. Water counts as hard above 150 mg/L as calcium carbonate. Softeners run on sodium chloride salt, and potassium chloride is the swap if you’re limiting sodium. |
| Rotten-egg smell from hydrogen sulfide | Aeration, chlorination or activated carbon | |
| Taste and odor problems | Activated carbon | which also catches some pesticides. It won’t effectively remove nitrate or bacteria. |
| Nitrate | Reverse osmosis or anion exchange | |
| Arsenic | Reverse osmosis, anion exchange or distillation | |
| Lead, fluoride and PFAS | Reverse osmosis; some certified carbon filters | reverse osmosis, according to the Minnesota Department of Health. Some carbon filters are certified for lead and fluoride, and the agency’s own study found granular carbon effective on PFAS. |
| Bacteria and viruses | UV disinfection or chlorination | A carbon filter after chlorination removes excess chlorine. |
No filter on this list does everything.
That’s why systems often stack stages in one setup, often with a sediment pre-filter first. UW Extension notes that sediment, tannins and cloudiness have to come out before UV light can reach the microorganisms. A softener may also be needed to keep scale off the UV lamp.
Latest county nitrate results for Cross Plains wells
The Dane County Land and Water Resources Department offered free nitrate tests to well owners across 10 western towns over 2024 and 2025. It was a volunteer sample, with owners signing up until the funds ran out.
The county collected 1,292 samples, analyzed by the Wisconsin State Laboratory of Hygiene. The average was 4.85 mg/L, and 10% were above the 10 mg/L federal limit set by the EPA.
In the Town of Cross Plains, sampled in 2025, 183 wells were tested, with an average of 5.25 mg/L. About 70% fell between 2 and 10 mg/L. Another 20% came in under 2 mg/L, and 10% were over the limit.
The county treats nitrate at or below 2 mg/L as generally natural. Higher readings show the effect of land use, such as fertilizer and manure. Most of the tested area sits in the Driftless Area, where thin soils and fractured bedrock leave groundwater more exposed.
That limit matters most for babies. The Wisconsin DNR says no infant, and no one who is or may become pregnant, should drink water above 10 mg/L or eat food made with it. All infants under 6 months are at risk, according to the same guidance.
Why the lab test comes before the filter
A lab test shows which problems your well actually has and how strong they are. Those two facts decide the type of filter and the size of the system.
The Wisconsin DNR recommends testing a private well for bacteria and nitrate once a year, and says most well users should test for arsenic every five years. Its list of certified labs is on the DNR well testing page.
Iron needs a fuller test. The DNR’s Iron in Drinking Water guide says it should cover iron, iron bacteria, manganese, pH, alkalinity and hardness. Together, those results show which treatment can work.
The same guide suggests five questions before you choose an iron system:
- What form of iron is in your water?
- Will the unit remove the total iron level your test found?
- Will it treat water at the flow rate your home needs?
- Will it work with your pH and other results?
- Would fixing the well itself cost less than years of treatment?
We can’t tell you which system you need from this page. Nobody can without your results.
That’s why Sauk Plains Plumbing & Pumps tests your water first and recommends a system based on what the results show. You can read more about well water filtration systems in Cross Plains and about annual well water testing.
Whole-house systems versus single-tap filters
A whole-house water filter or system, also called point-of-entry, treats all the water as it enters your home. A point-of-use filter treats water at one tap, usually the kitchen sink.
Point-of-entry makes sense when a problem affects everything the water touches, from fixtures to appliances. Iron stains laundry. Hardness causes scale buildup in hot water pipes and the water heater. Grit can plug pipes and even the water heater. Fixing those at one sink does nothing for the shower.
Point-of-use makes sense when the problem only matters for drinking and cooking. UW Extension notes that treating all the water in a house for a drinking-only problem is generally too expensive. Reverse osmosis is the usual example.
RO pushes water through a membrane with tiny pores, and it uses a lot of water. Only about 10% to 30% of the water entering a unit comes out treated, according to UW Extension, so the rest goes down the drain with the contaminants.
Some homes need both: a whole-house filter or softener for the plumbing, and an RO unit for drinking water.
If hardness is your main issue, our guide on choosing a water softener or water conditioner covers that decision.
What your stains say about iron in the water
Red or brown stains usually point to iron, and black specks point to manganese. Each one changes which filter will work, so the stain color is a useful first clue.
The DNR sorts iron into types. “Clear water” iron looks fine in the glass, then turns reddish brown as it sits. “Red water” iron comes out of the tap already rusty. Iron bound to tannins is usually yellow or brown and turns up more often in shallow wells.
Iron bacteria are their own problem. They leave a reddish brown or yellow slime that you may notice in the toilet tank when you lift the lid, and they can clog plumbing and cause a bad odor.
The DNR’s guideline for iron is 0.3 mg/L, and it’s about taste and appearance, not health.
Above that level, you’ll start to see rust stains on your laundry and fixtures. The water may taste metallic too.
Manganese often shows up alongside iron. It leaves black specks that smear into a black powder when you rub them. The DNR says to make sure your treatment device can remove the amount of both metals your test found.
No single treatment fixes every iron problem, according to the DNR. In some cases, changing a well’s casing or screen depth can cost less than treating the water, so the guide suggests comparing the cost of well work with perhaps 20 years of treatment.
How often do well water filters need changing?
Pentek rates the sediment cartridges in its Dura-Series manual for 2 to 4 months and its under-sink carbon cartridges for 3 to 12. Water conditions can shorten both.
Those figures come from the instructions for Pentek’s Dura-Series filter housings, the cartridge brand Sauk Plains Plumbing & Pumps installs. The finest cartridges wear out fastest. In that manual, the 5-micron sediment cartridges are rated for 2 months and the 50-micron ones for 4.
| Part | Typical change interval | Source |
|---|---|---|
| Whole-house sediment cartridge | Every 2 to 4 months | Pentek Dura-Series manual |
| Under-sink carbon cartridge | 3 to 12 months, depending on cartridge type | Pentek Dura-Series manual |
| Reverse osmosis system | Maintenance every 1 to 2 years | Minnesota Department of Health |
| UV system | Yearly upkeep | Minnesota Department of Health |
| Softener salt | Keep the brine tank stocked; $50 to $300 a year (2017–2018 Minnesota figures) | Minnesota Department of Health |
| Plastic filter housings | Clear: every 5 years; opaque: every 10 years | Pentek |
Wisconsin well water is often hard, and UW Extension warns that iron or sulfur bacteria can clog particle filters frequently. If your test shows either, plan for the shorter end of each range.
To slow clogging, deal with the cause upstream. UW Extension notes that dissolved iron and manganese may need pretreatment before a particle filter can catch them. Pentek adds that a cartridge’s lifespan depends on usage and water conditions.
The clearest sign shows up at the faucet. Pentek says a drop in water flow means the cartridge needs replacing, so it’s worth keeping replacement filters on hand.
Waiting too long has a cost. The Minnesota Department of Health warns that a carbon filter not replaced according to its instructions can saturate and start releasing contaminants back into the water. Sauk Plains Plumbing & Pumps lists water filter changes and annual service among its water treatment services.
Who can install a water treatment system in Wisconsin?
In Wisconsin, a treatment device needs a state product approval and a licensed plumber or pump installer, unless the owner fits it in the one-family home they live in.
Which license depends on where the device sits. Under Wisconsin’s well code, NR 812.37, a licensed plumber installs it after the pressure tank and a licensed pump installer installs it before the tank.
An owner working on the one-family home they own and live in is exempt, unless a local ordinance requires a license.
The Department of Safety and Professional Services lists approved devices by the contaminants each one removes, according to the DNR.
Bacteria come with an extra step. The code says treatment supplements proper well construction and doesn’t replace it. Before any device goes in to control bacteria, a licensed well driller or pump installer must inspect the well and pressure system.
Our page on what to do when a well water sample is unsafe walks through those steps.
Sauk Plains Plumbing & Pumps installs softeners, filters, reverse osmosis, UV, chlorination and de-chlorination systems. It has licensed plumbers and a licensed pump installer, so it can handle installation on either side of the pressure tank.
Wisconsin code also requires products in contact with drinking water to be certified to NSF/ANSI Standard 61 or approved by the DNR. Sauk’s products are certified by the Water Quality Association and installed to WQA standards, with Pentek filter cartridges and Reo-Pure reverse osmosis systems.
Questions about well water filters
Does well water need a filtration system?
Not always. Some wells test clean and need nothing at all. Private wells aren’t held to public water rules, and the Wisconsin DNR recommends testing them for bacteria and nitrate once a year. If a result shows a problem, such as nitrate above 10 mg/L or iron above 0.3 mg/L, the options are fixing the well or adding a system matched to that result. Sauk Plains Plumbing & Pumps tests first and recommends from the results.
How much is a whole house filtration system for well water?
The price depends on what the system has to remove, how much of it is in the water and the flow rate your home needs. Minnesota Department of Health estimates, based on 2017 to 2018 figures, put a whole-house UV unit at $250 to $800 and a softener at $200 to $3,000. Sauk Plains Plumbing & Pumps gives a free estimate before installing your system.
Will a water softener remove iron from well water?
Only a little. UW Extension says some softeners can remove a limited amount of iron and manganese when they are dissolved, and it lists softeners for hard water with low iron levels. The DNR adds that the hardness has to be calculated and the system must be airtight. UW Extension says iron filters are particularly useful when iron is between about 3 and 10 mg/L, or when you don’t want to soften the water.
Does a carbon filter remove nitrate?
No. UW Extension says activated carbon filters don’t effectively remove nitrate, arsenic or bacteria. Carbon is good at many taste and odor problems, plus some pesticides. For nitrate, the usual options are reverse osmosis or anion exchange. The federal limit is 10 mg/L, and about 10% of the Town of Cross Plains wells tested in 2025 came back above it.
Do I need a UV system for well water?
Usually only when testing finds bacteria and repairing the well hasn’t solved it. UV light kills bacteria, viruses and some cysts without chemicals. UW Extension says anything that blocks light, such as sediment or tannins, must come out first, and the lamp needs regular replacement. Wisconsin code also requires a licensed well driller or pump installer to inspect the well and pressure system before UV goes in to control bacteria.
Should I install a whole-house sediment filter before or after my pressure tank?
For Pentek’s whole-house housings, after it. Pentek’s instructions say its filter must be installed after the water meter or pressure tank. Some devices do go before the tank, and Wisconsin code lets a licensed pump installer fit those. A licensed plumber handles work after the tank, unless the homeowner does it. Sauk Plains Plumbing & Pumps has both licenses, so one call covers either side.
When to book a well water test and a filter install
Test once a year, and test again whenever the water changes color, taste or smell. Those are the DNR’s triggers for a bacteria test, and they’re also the right moment for you to check that your current filter still does its job.
Book the install after the results come back, not before. Buying a water filter for well water first and testing later risks a softener that can’t handle your iron, or carbon sitting in front of a nitrate problem. A test now can head off both.
Sauk Plains Plumbing & Pumps has served Middleton and western Dane County since 1934. Call 608-798-2121, email info@saukplainsplumbing.com or get in touch online to set up a water test in Cross Plains, Middleton, Verona, Waunakee or Black Earth.
